Installing Roof Shingles Starter Strip

Applying it on the eaves helps cover the joints between the finished shingles to provide waterproofing. Installing a starter shingle on your gables carries.

Gaf Timberline Hd Asphalt Shingles With Timbertex Ridge Cap Weather Watch In Leak Prone Areas And Prostart Starter Stri Roofing Systems Roofing House Styles

Installing roof shingles starter strip.

Installing roof shingles starter strip. Installing a starter shingle on your gables carries a different function from using it to the eaves. You will want the roof granular side up when applying the strip. / installing roof shingles starter strip.

Windsor® starter shingles share the same color blends as windsor®. Typically, manufacturers design starter strip shingles with a perforated line splitting them horizontally so that they can be easily separated and used with smaller shingles if necessary. How to shingle a roof:

Use with any shingle that has an exposure of up to 6. Otherwise, your roofing system won't seal properly. Align this side close to the lowest part of the roof.

Where drip edge extends out from the eave and rake edge, starter roll can be installed flush to the drip edge. Depending on the length of the shingle being installed, a 10 to12 inch section of starter strip may periodically need to be cut and installed to meet the required 4 inch offset. When installing your starter strips, offset the joins by at least 100mm to the joins of the roof shingle.

For maximum wind resistance, starter strips should be installed along all rake edges. This will prevent you from putting a join under a join, which won’t provide an. They are more expensive because they have to take the time to cut off the tabs.

It’s easy for a single person to position starter strip shingle on the roof. Apply asphalt shingles… as directed by the shingle manufacturer’s written application instructions. Remove the release film from the back of the roll and firmly press or roll into place along the rake edge (fig.

Use four nails on these starter shingles as shown on field shingle product wrap. After applying the starter shingles at the eaves, but prior to installing the field shingles, starter shingles may be applied up the slope at the rake edge with sealant facing out and nearest to the outer roof edge. Quickstart® peel & stick starter roll so that it overlaps the eave edge starter course by at least 3 (76 mm).

Applying starter strip shingles should fall on your roof’s eaves and gables or rake edges. Starter strip installation dmitry from storm group roofing is explaining the importance of installing starter strip vs using roofing s. Finally, a good contractor will make sure that the seams.

Using a utility knife, cut them off at the bottom of the adhesive strip. It is also important that the seal strip is placed facing up and close to the edge of your roof; A new roof is more than just shingles.

On a roof, it is recommended to mix shingles from 5 or 6 random bundles. Historically, starter strip shingles have been used not only at the lower eave edge of the roof, but experienced professionals also use them at the gable, or rake edges of roofs. For maximum wind resistance, starter strips should be installed along all rake edges.

Notice that the starter strip is installed in full width (two glue strips) with the glue strips facing up and the cellophane protective strip down (not in view here). Before peeling the shingle starter strip, trim about 4 inches off an end of the first starter strip and align the strip to the area you are planning to stick it on. On a roof, it is recommended to mix shingles from 5 or 6 random bundles.

Installing roof shingles starter strip. Speeds installation and helps improve safety. The first layer will be laid down with the full shingles flush against the starter strip.

Starter strip shingle eliminates the need to cut off tabs or headlap. Fasten the adjustment starter strip with two nails one to two inches from each side end. To begin installing the first shingles on your roof, cut off the three tabs on the shingle.

On a roof, it is recommended to mix shingles from 5 or 6 random bundles. See the benefits of starter strip shingles. The end should overhang over the edge about 1/4 to 3/4 of an inch.

Finally, a good contractor will make sure that the seams. Installing roof shingles starter strip.

Illustrated Diagram Of Roofing System Layers Roofing Asphalt Roof Shingles Roof Shingles