Installing Shingle Starter Course

Starter shingles are the initial shingle products installed on the roof, just before the first course of the finish shingles, which will comprise the visible parts of the roof. Starter course & first row.

How To Install Asphalt Shingles Make Starter Strip From Shingles Roofing Building A Shed Installing Roof Shingles

The starter course should overhang the bottom of the wall or the facer of a roof by a minimum of 3/4 inch.

Installing shingle starter course. • apply in dry weather at recommended temperatures of 40º f,. You will shingle over this starter course, so. Then, the first row is simply installed over the starter course, keeping the gaps between the shingles staggered from the gaps of the starter course.

Finally, one of the benefits of applying a starter shingle on your eaves and gables is it gives your roofer a straight line to follow as a guide. The starter strip is installed next, and usually lines up with the bottom of the wall, 2 inches from any masonry, depending on the project. Control line and nail them down, four nails per shingle.

Keep the individual shingle tabs to use as finishing pieces. Starter course • rip cut a 9” starter course from the top of a full panel. Place the glue strip at and all along the drip edge as well as the rake edges.

16 from center to the left and right *panels can also be installed direct to stud up to 24oc. Installing starter shingle roll.with the starter shingles laid along the very edge of the roof, run a set of starter shingles along the sides of the roof as well, making sure that those rows come down and overlap the starter. First, trim 5 inches off of the left side of the first shingle in the second course.

The starter course is the bottom row you install. Starter course • rip cut a 9” starter course from the top of a full panel. Of starter course 8¼ starter course in line with starter strip 15.25 7.00 snap chalk line;

Locate the bottom of the next row, install, and so on all the way up the wall. To prepare the tabs and lay the starter course, shorten the first starter shingle by 6 inches (or about a half of one tab). Specifically, a starter shingle on your gables improves your roof’s wind resistance.

Installation of starter strip shingle starter strip shingle is designed to be broken into two pieces, and each piece has its own sealant strip. Starter course • rip cut a 9” starter course from the top of a full panel. [figure 7] another method consists of installing the first course using shingles trimmed 5 from the base, then continuing the.

The starter course serves to fill the gaps in the first exposed course of shingles. Keep the individual shingle tabs to use as finishing pieces. When separated, each starter shingle is 65⁄ 8 x 393⁄ 8, and each bundle will cover approximately 105 lineal feet.

Effectively staggering your architectural shingles begins with the installation of the second course. Place the glue strip at and all along the drip edge as well as the rake edges. This starter can be used with shingles that have an exposure of no more

If you are making your own starter shingles, cut the tabs off for the starter course (bottom row) of shingles. Keep the individual shingle tabs to use as finishing pieces. Snapped chalk lines help guide installation, when installing straight edge panels or individual shingles use a straight edge on bottom edges if uniform.

Trim 5 (127 mm) and apply as shown (see figure 2). The starter board is just a very straight, horizontal board used to hold the first. First course of shingles installed along the drip edge at the eaves below the first exposed course of shingles.

Shingle installation begins with starter shingles that are installed along the eave and rake edges. Since the starter shingles will be covered by the roof shingles, it doesn’t matter what color they. Continue on with installing full shingles.

Place the glue strip at and all along the drip edge as well as the rake edges. The starter course has two layers of shingles. Installing a starter shingle on your gables carries a different function from using it to the eaves.

The first exposed course of shingles should be flush with or,.

Close Up Of Slate Roofer Installing The Starter Slates And First And Second Courses With North Country Slate Roof Installation Roof Installation North Country