Why Is My Viper Remote Start Not Working

If you have a brand other than compustar you should look for a small toggle switch and see if it accidentally got flipped. Thank you for purchasing this viper remote transmitter.

Clifford 5906X WITH VIPER REMOTE CONTROL 7944V YouTube

If you have 2 keys that start the car follow these instructions exactly.

Why is my viper remote start not working. It is a subaru manual car, but configured as auto to skip the shutdown procedure that is required by remote start to work. My vehicle remote starts but then immediately shuts off. I tried 2 different cables and also tried charging from laptop, ps3 and straight from plug aswell.

I do not know where the toggle switch is and how it got turned off. It is a black wire with a white stripe and is located in the viper remote start system. If they no longer flash when you ask your vehicle to lock or unlock using the remote starter controller, you may be in valet mode.

All the newer le and refurbished ones come with the 7153v remotes. The remote vehicle start (rvs) system will not operate if any of the following conditions are present: If the ‘check engine light’ or malfunction indicator lamp (mil) is illuminated, the remote start system will not work.

^ keyless entry transmitter is not. Never had a vehicles remotes stop working when the battery got low. Anyone knows what the issue might be ?

After the 'theft' light goes out (in the gauge cluster) turn off and remove key. When i pushed buttons to get the flashing tail lights on the car, it flashed 8 times, which indicated toggle switch off. If this does not work turn the key off then back on and try it three times.

Check if your remote is paired correctly; This product does everything you need, the best part is by the led confirmation, you will know if your car starts. Hi all, replaced the car battery.

Oh and i need to add this.it may be your bypass. I had it installed professionally by one of the viper dealers here in los angeles. While keeping your foot on the brake, press the remote start button on your remote control for 3 seconds like you are remote starting the vehicle.

If you can lock and unlock your doors just fine but only the remote start does not work, you may be in valet mode. My remote starter is not working. Press and hold the foot brake down.

I am assuming it must be under my dash, but i cannot find it. Don’t panic, one of the reasons the mil can illuminate is due to a loose gas cap! Insert key into the ignition, and turn to the on position (not start) 2.

Did you try deleting all remotes (step 2)and start fresh. I have a viper remote start, model #7857v. I got this for my daughter last year and for me, and it works like a charm.

Remote start has been working close to 3 months. Reseal the cap, restart the car, and retry step #1! This may not be a typical case, but it can sometimes occur.

(if they flash more than once, you may have to visit the dealer/installer) turn the vehicle off. This device complies with part 15 of fcc rules. Hello, i think i have the viper 5706v installed with the smart start gps on my 2014 lancer evolution x mr.

My husband has a remote start the dealership put in, and if you're not close to the vehicle to hear the horn beep, you're out of luck. Push to start vehicle shuts off as soon as i open the door. Radio presets gone but otherwise ok except remote start.

Why is my viper alarm not working? Post by stiege » thu dec 12, 2013 9:02 pm. Immediately insert second key (not same as in step 1) and turn to the on position.

If the procedure mentioned above does not work simply turn the key off then back on and press the valet switch two times. This guide provides a general description of operations for viper remote start systems. How do i exit and/or enter valet mode?

Parking light flashes | troubleshooting your remote starter; What model of remotes 7152v or 7253v? Your parking lights will flash once.

Here is how to check.unplug your bypass and put the factory key in the ignition.do not start or turn it, just slide it in.remote start it.if it runs fine, well you have your answer.if it doesnt, well you had to take the dash apart anyways lol.toyotas arent bad, if it were a bmw, id have a tear for ya. If that don't work got to any authorized dei installer and have them test them. Press and hold single button fob, locks lock, get chirp, then instead of starting it.

I waited a min to see if it would learn and nothing so i took it apart, removed the battery for a sec then reinstalled it and that did the trick. You can try taking out the batterys and let them set over night, put fresh batteries in them a try again. So far there is no problem until few days ago.

One way you may be able to tell if your vehicle is in valet mode is by watching the parking lights. Hey, i have viper 5901 system in my car. Many remote starter systems will use a switch to put the system in valet mode.

Both remotes working fine again and the battery is charged up for this weekends drive. Operation is subject to the following two conditions: Got the second remote and it still didnt work.

I've had to go back to that shop a few times now because of various problems (kind of wizzed off since i work full time and t rying to study for the mcat). If you find one, simply flip the switch the opposite direction and attempt the remote start again. To solve this, you will need to start by replacing the batteries with a new one and see if it works.

Remote start not working after car battery replacement.

Why Is My Viper Remote Start Not Working Inspire Ideas